Inspecting /boot/System.map-2.6.8-24-default Loaded 23888 symbols from /boot/System.map-2.6.8-24-default. Symbols match kernel version 2.6.8. No module symbols loaded - kernel modules not enabled. klogd 1.4.1, log source = ksyslog started. <4>Linux version 2.6.8-24-default (geeko@buildhost) (gcc version 3.3.4 (pre 3.3.5 20040809)) #1 Wed Oct 6 09:16:23 UTC 2004 <6>BIOS-provided physical RAM map: <4> BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) <4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) <4> BIOS-e820: 0000000000100000 - 000000007fff0000 (usable) <4> BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS) <4> BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data) <4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) <5>128MB vmalloc/ioremap area available. <5>1151MB HIGHMEM available. <5>896MB LOWMEM available. <7>On node 0 totalpages: 524272 <7> DMA zone: 4096 pages, LIFO batch:1 <7> Normal zone: 225280 pages, LIFO batch:16 <7> HighMem zone: 294896 pages, LIFO batch:16 <6>DMI 2.2 present. <6>ACPI: RSDP (v000 GBT ) @ 0x000f6190 <6>ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x7fff3000 <6>ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x7fff3040 <6>ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 <6>ACPI: PM-Timer IO Port: 0x4008 <6>ACPI: local apic disabled <4>Built 1 zonelists <4>Kernel command line: root=/dev/md2 vga=0x31a selinux=0 resume=/dev/md1 desktop elevator=as splash=silent <6>bootsplash: silent mode. <6>Initializing CPU#0 <4>PID hash table entries: 4096 (order: 12, 65536 bytes) <4>Detected 1466.927 MHz processor. <6>Using pmtmr for high-res timesource <4>Console: colour dummy device 80x25 <4>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <4>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>Memory: 2073868k/2097088k available (2074k kernel code, 22260k reserved, 782k data, 212k init, 1179584k highmem) <4>Checking if this processor honours the WP bit even in supervisor mode... Ok. <7>Calibrating delay loop... 2908.16 BogoMIPS (lpj=1454080) <6>Security Scaffold v1.0.0 initialized <6>SELinux: Disabled at boot. <4>Mount-cache hash table entries: 512 (order: 0, 4096 bytes) <7>CPU: After generic identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 <7>CPU: After vendor identify, caps: 0383f9ff c1cbf9ff 00000000 00000000 <6>CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) <6>CPU: L2 Cache: 256K (64 bytes/line) <7>CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000020 <6>Intel machine check architecture supported. <6>Intel machine check reporting enabled on CPU#0. <4>CPU: AMD Athlon(tm) XP 1700+ stepping 02 <6>Enabling fast FPU save and restore... done. <6>Enabling unmasked SIMD FPU exception support... done. <6>Checking 'hlt' instruction... OK. <4>ACPI: IRQ9 SCI: Level Trigger. <6>checking if image is initramfs...it isn't (no cpio magic); looks like an initrd <6>Looking for DSDT in initrd ...No customized DSDT found in initrd! <6>Freeing initrd memory: 1455k freed <6>NET: Registered protocol family 16 <6>PCI: PCI BIOS revision 2.10 entry at 0xfb600, last bus=1 <6>PCI: Using configuration type 1 <6>mtrr: v2.0 (20020519) <6>ACPI: Subsystem revision 20040715 <6>ACPI: Interpreter enabled <6>ACPI: Using PIC for interrupt routing <6>ACPI: PCI Root Bridge [PCI0] (00:00) <4>PCI: Probing PCI hardware (bus 00) <4>PCI: fixing NCR 53C810 class code for 0000:00:09.0 <7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] <4>ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 *12 14 15) <4>ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15) <4>ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) <6>Linux Plug and Play Support v0.97 (c) Adam Belay <6>PCI: Using ACPI for IRQ routing <4>ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 <6>ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 10 (level, low) -> IRQ 10 <4>ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 <6>ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 5 (level, low) -> IRQ 5 <4>ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12 <6>ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 12 (level, low) -> IRQ 12 <6>ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 10 (level, low) -> IRQ 10 <4>ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 <6>ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 11 (level, low) -> IRQ 11 <6>ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 12 (level, low) -> IRQ 12 <4>TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca) <6>apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) <5>apm: overridden by ACPI. <6>audit: initializing netlink socket (disabled) <3>audit(1106613295.4294965570:0): initialized <4>highmem bounce pool size: 64 pages <4>Total HugeTLB memory allocated, 0 <5>VFS: Disk quotas dquot_6.5.1 <4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>Initializing Cryptographic API <6>PCI: Disabling Via external APIC routing <6>vesafb: framebuffer at 0xd7000000, mapped to 0xf8880000, using 8192k, total 8192k <6>vesafb: mode is 1280x1024x16, linelength=2560, pages=0 <6>vesafb: protected mode interface info at c000:79e0 <6>vesafb: scrolling: redraw <6>vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 <6>bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 47601 bytes,<6>...found (1280x1024, 24984 bytes, v3). <4>Console: switching to colour frame buffer device 158x57 <6>fb0: VESA VGA frame buffer device <6>isapnp: Scanning for PnP cards... <6>isapnp: No Plug & Play device found <6>Real Time Clock Driver v1.12 <6>serio: i8042 KBD port at 0x60,0x64 irq 1 <6>serio: i8042 AUX port at 0x60,0x64 irq 12 <6>Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled <4>Using anticipatory io scheduler <6>Floppy drive(s): fd0 is 1.44M <6>FDC 0 is a post-1991 82077 <4>RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize <6>loop: loaded (max 8 devices) <6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 <6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx <6>VP_IDE: IDE controller at PCI slot 0000:00:07.1 <6>VP_IDE: chipset revision 6 <6>VP_IDE: not 100%% native mode: will probe irqs later <6>VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1 <6> ide0: BM-DMA at 0xd400-0xd407, BIOS settings: hda:DMA, hdb:pio <6> ide1: BM-DMA at 0xd408-0xd40f, BIOS settings: hdc:pio, hdd:pio <7>Probing IDE interface ide0... <4>hda: TOSHIBA CD-ROM XM-6702B, ATAPI CD/DVD-ROM drive <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <7>Probing IDE interface ide1... <7>ide1: Wait for ready failed before probe ! <7>Probing IDE interface ide1... <7>ide1: Wait for ready failed before probe ! <7>Probing IDE interface ide2... <7>ide2: Wait for ready failed before probe ! <7>Probing IDE interface ide3... <7>ide3: Wait for ready failed before probe ! <7>Probing IDE interface ide4... <7>ide4: Wait for ready failed before probe ! <7>Probing IDE interface ide5... <7>ide5: Wait for ready failed before probe ! <4>ide-floppy driver 0.99.newide <6>mice: PS/2 mouse device common for all mice <6>input: PC Speaker <6>md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 <6>NET: Registered protocol family 2 <6>IP: routing cache hash table of 16384 buckets, 128Kbytes <6>TCP: Hash tables configured (established 524288 bind 65536) <6>NET: Registered protocol family 1 <6>NET: Registered protocol family 8 <6>NET: Registered protocol family 20 <7>PM: Reading pmdisk image. <7>swsusp: Resume From Partition: /dev/md1 <7>pmdisk: Error -6 resuming <7>PM: Resume from disk failed. <6>ACPI: (supports S0 S1 S4 S5) <4>ACPI wakeup devices: <4>SLPB PCI0 USB0 USB1 <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: ... autorun DONE. <5>RAMDISK: Compressed image found at block 0 <4>VFS: Mounted root (ext2 filesystem). <5>SCSI subsystem initialized <6>qla1280: QLA1080 found on PCI bus 0, dev 12 <6>ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 12 (level, low) -> IRQ 12 <6>scsi(0): Reading NVRAM <6>scsi(0:0): Resetting SCSI BUS <6>scsi0 : QLogic QLA1080 PCI to SCSI Host Adapter <4> Firmware version: 8.15.00, Driver version 3.24.4 <5> Vendor: HITACHI Model: DK319H-18WC Rev: H18F <5> Type: Direct-Access ANSI SCSI revision: 02 <6>scsi(0:0:0:0): Sync: period 10, offset 8, Wide, Tagged queuing: depth 255 <5>SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB) <5>SCSI device sda: drive cache: write back <6> sda: sda1 sda2 sda3 <5>Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 <5> Vendor: HITACHI Model: DK319H-18WC Rev: H18F <5> Type: Direct-Access ANSI SCSI revision: 02 <6>scsi(0:0:1:0): Sync: period 10, offset 8, Wide, Tagged queuing: depth 255 <5>SCSI device sdb: 35566480 512-byte hdwr sectors (18210 MB) <5>SCSI device sdb: drive cache: write back <6> sdb: sdb1 sdb2 sdb3 <5>Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 <6>ACPI: PCI interrupt 0000:00:0f.0[A] -> GSI 11 (level, low) -> IRQ 11 <4>qlogicfc0 : Loop Reinitialized <4>qlogicfc0 : Link is Up <6>scsi1 : QLogic ISP2100 SCSI on PCI bus 00 device 78 irq 11 base 0xec00 <4>qlogicfc0 : Port Database <4>wwn: 200000e08b002e85 scsi_id: 0 loop_id: 4 <4>wwn: 50000e1000018bcc scsi_id: 1 loop_id: 0 <4>wwn: 50000e100001c901 scsi_id: 2 loop_id: 1 <4>wwn: 50000e100001da05 scsi_id: 3 loop_id: 2 <4>wwn: 50000e100001bbc6 scsi_id: 4 loop_id: 3 <5> Vendor: HITACHI Model: DK31CJ-72FC Rev: GGN3 <5> Type: Direct-Access ANSI SCSI revision: 02 <5>SCSI device sdc: 144410880 512-byte hdwr sectors (73938 MB) <5>SCSI device sdc: drive cache: write back <6> sdc: sdc1 <5>Attached scsi disk sdc at scsi1, channel 0, id 1, lun 0 <5> Vendor: HITACHI Model: DK31CJ-72FC Rev: GGN3 <5> Type: Direct-Access ANSI SCSI revision: 02 <5>SCSI device sdd: 144410880 512-byte hdwr sectors (73938 MB) <5>SCSI device sdd: drive cache: write back <6> sdd: sdd1 <5>Attached scsi disk sdd at scsi1, channel 0, id 2, lun 0 <5> Vendor: HITACHI Model: DK31CJ-72FC Rev: GGN3 <5> Type: Direct-Access ANSI SCSI revision: 02 <5>SCSI device sde: 144410880 512-byte hdwr sectors (73938 MB) <5>SCSI device sde: drive cache: write back <6> sde: sde1 <5>Attached scsi disk sde at scsi1, channel 0, id 3, lun 0 <5> Vendor: HITACHI Model: DK31CJ-72FC Rev: GGN3 <5> Type: Direct-Access ANSI SCSI revision: 02 <5>SCSI device sdf: 144410880 512-byte hdwr sectors (73938 MB) <5>SCSI device sdf: drive cache: write back <6> sdf: sdf1 <5>Attached scsi disk sdf at scsi1, channel 0, id 4, lun 0 <6>ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 10 (level, low) -> IRQ 10 <6>sym0: <810> rev 0x1 at pci 0000:00:09.0 irq 10 <4>sym0: No NVRAM, ID 7, Fast-10, SE, parity checking <5>sym0: SCSI BUS has been reset. <6>scsi2 : sym-2.1.18j <6>md: raid1 personality registered as nr 3 <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: considering sdf1 ... <6>md: adding sdf1 ... <4>md: sde1 has different UUID to sdf1 <6>md: adding sdd1 ... <4>md: sdc1 has different UUID to sdf1 <4>md: sdb3 has different UUID to sdf1 <4>md: sdb2 has different UUID to sdf1 <4>md: sdb1 has different UUID to sdf1 <4>md: sda3 has different UUID to sdf1 <4>md: sda2 has different UUID to sdf1 <4>md: sda1 has different UUID to sdf1 <6>md: created md4 <6>md: bind <6>md: bind <6>md: running: <6>raid1: raid set md4 active with 2 out of 2 mirrors <6>md: considering sde1 ... <6>md: adding sde1 ... <6>md: adding sdc1 ... <4>md: sdb3 has different UUID to sde1 <4>md: sdb2 has different UUID to sde1 <4>md: sdb1 has different UUID to sde1 <4>md: sda3 has different UUID to sde1 <4>md: sda2 has different UUID to sde1 <4>md: sda1 has different UUID to sde1 <6>md: created md3 <6>md: bind <6>md: bind <6>md: running: <4>md: kicking non-fresh sde1 from array! <6>md: unbind <6>md: export_rdev(sde1) <6>raid1: raid set md3 active with 1 out of 2 mirrors <6>md: considering sdb3 ... <6>md: adding sdb3 ... <4>md: sdb2 has different UUID to sdb3 <4>md: sdb1 has different UUID to sdb3 <6>md: adding sda3 ... <4>md: sda2 has different UUID to sdb3 <4>md: sda1 has different UUID to sdb3 <6>md: created md2 <6>md: bind <6>md: bind <6>md: running: <6>raid1: raid set md2 active with 2 out of 2 mirrors <6>md: considering sdb2 ... <6>md: adding sdb2 ... <4>md: sdb1 has different UUID to sdb2 <6>md: adding sda2 ... <4>md: sda1 has different UUID to sdb2 <6>md: created md1 <6>md: bind <6>md: bind <6>md: running: <6>raid1: raid set md1 active with 2 out of 2 mirrors <6>md: considering sdb1 ... <6>md: adding sdb1 ... <6>md: adding sda1 ... <6>md: created md0 <6>md: bind <6>md: bind <6>md: running: <6>raid1: raid set md0 active with 2 out of 2 mirrors <6>md: ... autorun DONE. <5>ReiserFS: md2: found reiserfs format "3.6" with standard journal <5>ReiserFS: md2: using ordered data mode <4>reiserfs: using flush barriers <5>ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: md2: checking transaction log (md2) <5>ReiserFS: md2: Using r5 hash to sort names <4>VFS: Mounted root (reiserfs filesystem) readonly. <5>Trying to move old root to /initrd ... failed <5>Unmounting old root <5>Trying to free ramdisk memory ... okay <6>Freeing unused kernel memory: 212k freed <6>Adding 2104440k swap on /dev/md1. Priority:42 extents:1 <4>reiserfs: enabling write barrier flush mode <6>usbcore: registered new driver usbfs <6>usbcore: registered new driver hub <6>e100: Intel(R) PRO/100 Network Driver, 3.0.27-k2-NAPI <6>e100: Copyright(c) 1999-2004 Intel Corporation <6>ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 5 (level, low) -> IRQ 5 <6>e100: eth0: e100_probe: addr 0xd9108000, irq 5, MAC addr 00:08:C7:EB:3E:48 <4>md: raidstart(pid 2417) used deprecated START_ARRAY ioctl. This will not be supported beyond 2.6 <3>md: could not bd_claim sda1. <4>md: autostart failed! <4>md: raidstart(pid 2417) used deprecated START_ARRAY ioctl. This will not be supported beyond 2.6 <3>md: could not bd_claim sda2. <4>md: autostart failed! <4>md: raidstart(pid 2417) used deprecated START_ARRAY ioctl. This will not be supported beyond 2.6 <3>md: could not bd_claim sda3. <4>md: autostart failed! <3>md: could not bd_claim sdc1. <4>md: autostart failed! <3>md: could not bd_claim sdd1. <4>md: autostart failed! <6>md: Autodetecting RAID arrays. <6>md: autorun ... <6>md: considering sde1 ... <6>md: adding sde1 ... <4>md: md3 already running, cannot run sde1 <6>md: export_rdev(sde1) <6>md: ... autorun DONE. <6>device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com <6>parport_pc: Via 686A parallel port disabled in BIOS <7>ieee1394: Initialized config rom entry `ip1394' <6>ohci1394: $Rev: 1223 $ Ben Collins <6>ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 10 (level, low) -> IRQ 10 <6>ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[d9107000-d91077ff] Max Packet=[2048] <6>Linux agpgart interface v0.100 (c) Dave Jones <6>agpgart: Detected AMD 761 chipset <6>agpgart: Maximum main memory to use for agp memory: 1919M <6>agpgart: AGP aperture is 64M @ 0xd0000000 <5>ReiserFS: md0: found reiserfs format "3.6" with standard journal <5>ReiserFS: md0: using ordered data mode <4>reiserfs: using flush barriers <5>ReiserFS: md0: journal params: device md0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 <5>ReiserFS: md0: checking transaction log (md0) <5>ReiserFS: md0: Using r5 hash to sort names <6>subfs 0.9 <7>ieee1394: Host added: ID:BUS[0-00:1023] GUID[0000000000000000] <7>ISO 9660 Extensions: Microsoft Joliet Level 3 <7>ISO 9660 Extensions: RRIP_1991A Kernel logging (ksyslog) stopped. Kernel log daemon terminating. Boot logging started on /dev/tty1(/dev/console) at Mon Jan 24 16:35:35 2005 run boot scripts (setserial boot.proc) Configuring serial ports... Configured serial ports doneexit status of (setserial boot.proc) is (0 0) run boot scripts (boot.shm) Mounting shared memory FS on /dev/shmdone exit status of (boot.shm) is (0) run boot scripts (boot.rootfsck) Activating swap-devices in /etc/fstab... doneChecking root file system... fsck 1.35 (28-Feb-2004) Reiserfs super block in block 16 on 0x902 of format 3.6 with standard journal Blocks (total/free): 3891728/1048303 by 4096 bytes Filesystem is clean Filesystem seems mounted read-only. Skipping journal replay. Checking internal tree..finished doneexit status of (boot.rootfsck) is (0) run boot scripts (boot.hotplug) Hotplug is already active (disable with NOHOTPLUG=1 at the boot prompt)done exit status of (boot.hotplug) is (0) run boot scripts (boot.coldplug) coldplug scanning input: *done scanning pci: ***.*.*.**Wdone scanning usb: done done exit status of (boot.coldplug) is (0) run boot scripts (boot.md boot.device-mapper) Initializing Multiple Devices... considering /dev/md0... /dev/md0 is not a RAID0 or LINEAR array, skipping. considering /dev/md1... /dev/md1 is not a RAID0 or LINEAR array, skipping. considering /dev/md2... /dev/md2 is not a RAID0 or LINEAR array, skipping. considering /dev/md3... /dev/md3 is not a RAID0 or LINEAR array, skipping. considering /dev/md4... /dev/md4 is not a RAID0 or LINEAR array, skipping. /dev/md0: Invalid argument /dev/md1: Invalid argument /dev/md2: Invalid argument /dev/md3: Invalid argument /dev/md4: Invalid argument Activating device mapper... Creating /dev/mapper/control character device with major:10 minor:63. done exit status of (boot.md boot.device-mapper) is (0 0) run boot scripts (boot.lvm) Scanning for LVM volume groups... Reading all physical volumes. This may take a while... Found volume group "system" using metadata type lvm2 Activating LVM volume groups... 2 logical volume(s) in volume group "system" now active done exit status of (boot.lvm) is (0) run boot scripts (boot.localfs) Checking file systems... fsck 1.35 (28-Feb-2004) Reiserfs super block in block 16 on 0x900 of format 3.6 with standard journal Blocks (total/free): 26080/16376 by 4096 bytes Filesystem is clean Replaying journal.. Reiserfs journal '/dev/md0' in blocks [18..8211]: 0 transactions replayed Checking internal tree..finished doneSetting up kernel module dependencies (if required)done Mounting local file systems... proc on /proc type proc (rw) tmpfs on /dev/shm type tmpfs (rw) devpts on /dev/pts type devpts (rw,mode=0620,gid=5) /dev/md0 on /boot type reiserfs (rw,acl,user_xattr) /dev/hda on /media/cdrom type subfs (ro,nosuid,nodev,fs=cdfss,procuid,iocharset=utf8) /dev/fd0 on /media/floppy type subfs (rw,nosuid,nodev,sync,fs=floppyfss,procuid) mount: going to use the loop device /dev/loop0 /suse/suse92-disk1.iso on /suse/suse92-disk1 type iso9660 (ro,loop=/dev/loop0) doneexit status of (boot.localfs) is (0) run boot scripts (boot.scpm boot.loadmodules boot.klog) Loading required kernel modules doneCreating /var/log/boot.msg donekillproc: kill(1963,29) exit status of (boot.scpm boot.loadmodules boot.klog) is (0 0 0) run boot scripts (boot.crypto) exit status of (boot.crypto) is (0) run boot scripts (boot.swap boot.restore_permissions boot.idedma) Restore device permissionsdone Disk /dev/md4 doesn't contain a valid partition table Disk /dev/md3 doesn't contain a valid partition table Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1 doesn't contain a valid partition table Activating remaining swap-devices in /etc/fstab... doneexit status of (boot.swap boot.restore_permissions boot.idedma) is (0 0 0) run boot scripts (boot.clock) Setting up the CMOS clockdone exit status of (boot.clock) is (0) run boot scripts (boot.ldconfig) Setting up timezone datadone exit status of (boot.ldconfig) is (0) run boot scripts (boot.sysctl boot.localnet boot.isapnp) Setting current sysctl status from /etc/sysctl.conf net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.rp_filter = 1 done Setting up hostname 'gene'done Setting up loopback interface lo lo IP address: 127.0.0.1/8 done exit status of (boot.sysctl boot.localnet boot.isapnp) is (0 0 0) run boot scripts (boot.ipconfig) Enabling syn flood protectiondone Disabling IP forwardingdone done System Boot Control: The system has been set up System Boot Control: Running /etc/init.d/boot.local doneexit status of (boot.ipconfig) is (0) killproc: kill(1963,3) INIT: Entering runlevel: 5 Boot logging started on /dev/tty1(/dev/console) at Mon Jan 24 16:35:57 2005 Master Resource Control: previous runlevel: N, switching to runlevel: 5 start services (random isdn SuSEfirewall2_init) Initializing random number generatordone Starting Firewall Initialization (phase 1 of 3) done exit status of (random isdn SuSEfirewall2_init) is (0 0 0) start services (network) Setting up network interfaces: lo lo IP address: 127.0.0.1/8 done eth0 device: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 05) eth0 configuration: eth-id-00:08:c7:eb:3e:48 eth0 (DHCP) . IP/Netmask: 192.168.1.19 / 255.255.255.0 doneSetting up service network . . . . . . . . . . . . . . . .done exit status of (network) is (0) start services (syslog) Starting syslog servicesstartproc: execve (/sbin/syslogd) [ /sbin/syslogd -a /var/lib/ntp/dev/log ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/sbin/syslogd ] startproc: execve (/sbin/klogd) [ /sbin/klogd -c 1 -2 -x ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/sbin/klogd ] done exit status of (syslog) is (0) start services (SuSEfirewall2_setup) Starting Firewall Initialization (phase 2 of 3) WARNING: Error inserting ipfwadm (/lib/modules/2.6.8-24-default/kernel/net/ipv4/netfilter/ipfwadm.ko): Device or resource busy SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 done exit status of (SuSEfirewall2_setup) is (0) start services (vmware splash_early resmgr portmap) startproc: execve (/sbin/resmgrd) [ /sbin/resmgrd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/sbin/resmgrd ] Starting resource managerdone startproc: execve (/sbin/portmap) [ /sbin/portmap ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/sbin/portmap ] Starting RPC portmap daemondone Starting VMware services: Virtual machine monitor done Virtual ethernet done Bridged networking on /dev/vmnet0 done exit status of (vmware splash_early resmgr portmap) is (0 0 0 0) start services (nfsboot nfs) Starting nfsboot (sm-notify) done Importing Net File System (NFS)unused exit status of (nfsboot nfs) is (0 6) start services (sshd running-kernel fbset alsasound) startproc: execve (/usr/sbin/sshd) [ /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pid ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/usr/sbin/sshd ] Starting SSH daemondone Starting sound driverdone exit status of (sshd running-kernel fbset alsasound) is (0 0 0 0) start services (xdm splash powersaved kbd cups) startproc: execve (/opt/kde3/bin/kdm) [ /opt/kde3/bin/kdm ], [ LC_MONETARY= CONSOLE=/dev/console TERM=linux SHELL=/bin/sh LC_NUMERIC= QTDIR=/usr/lib/qt3 LC_ALL= INIT_VERSION=sysvinit-2.85 KDEROOTHOME=/root/.kdm REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin LC_MESSAGES= vga=0x31a RUNLEVEL=5 LC_COLLATE= PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg LANG=en_US.UTF-8 PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 XCURSOR_THEME=crystalwhite WINDOWMANAGER=/usr/X11R6/bin/kde LC_CTYPE=en_US.UTF-8 splash=silent SPLASH=yes LC_TIME= _=/sbin/startproc DAEMON=/opt/kde3/bin/kdm ] Starting service kdmdone startproc: execve (/usr/sbin/cupsd) [ /usr/sbin/cupsd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/usr/sbin/cupsd ] Starting cupsddone startproc: execve (/usr/sbin/powersaved) [ /usr/sbin/powersaved -d -x /usr/lib/powersave/scripts -a resmgr -v 3 ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/usr/sbin/powersaved ] loading ACPI modules (ac battery button fan processor thermal ) done Starting powersaved (accessing ACPI events over acpid) done Loading keymap qwerty/us.map.gz doneLoading compose table winkeys shiftctrl latin1.adddone Start Unicode mode doneLoading console font lat9w-16.psfu -m trivial \033(K doneexit status of (xdm splash powersaved kbd cups) is (0 0 0 0 0) start services (postfix nscd hwscan) Starting mail service (Postfix)done Starting Name Service Cache Daemonstartproc: execve (/usr/sbin/nscd) [ /usr/sbin/nscd ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/usr/sbin/nscd ] done Starting hardware scan on bootexit status of (postfix nscd hwscan) is (0 0 0) start services (smbfs cron) Mount SMB/ CIFS File Systems unused Starting CRON daemonstartproc: execve (/usr/sbin/cron) [ /usr/sbin/cron ], [ CONSOLE=/dev/console TERM=linux SHELL=/bin/sh INIT_VERSION=sysvinit-2.85 REDIRECT=/dev/tty1 COLUMNS=158 PATH=/usr/local/sbin:/sbin:/bin:/usr/sbin:/usr/bin vga=0x31a RUNLEVEL=5 PWD=/ SPLASHCFG=/etc/bootsplash/themes/SuSE/config/bootsplash-1280x1024.cfg PREVLEVEL=N LINES=57 HOME=/ SHLVL=2 splash=silent SPLASH=yes _=/sbin/startproc DAEMON=/usr/sbin/cron ] done exit status of (smbfs cron) is (6 0) start services (SuSEfirewall2_final) Starting Firewall Initialization (phase 3 of 3) WARNING: Error inserting ipfwadm (/lib/modules/2.6.8-24-default/kernel/net/ipv4/netfilter/ipfwadm.ko): Device or resource busy SuSEfirewall2: Firewall rules successfully set from /etc/sysconfig/SuSEfirewall2 done exit status of (SuSEfirewall2_final) is (0) Master Resource Control: runlevel 5 has been reached Skipped services in runlevel 5: nfs smbfs killproc: kill(3340,3) checkproc: /opt/kde3/bin/kdm 5233